Pass4sure 200-101 Question Answer

Which protocol provides a method of sharing VLAN configuration information between two Cisco switches?

A. STP
B. VTP
C. 802.1Q
D. RSTP

Answer: B


Which two statements describe the process identifier that is used in the command to configure OSPF on a router? (Choose two.)


A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.

Answer: CD
                   
          200-101 Practice Dumps       300-070 BrainDumps     Cisco Practice Exams Test

Pass4sure 200-101 Question Answer

What are two characteristics of a switch that is configured as a VTP client? (Choose two.)

A. If a switch that is configured to operate in client mode cannot access a VTP server, then the switch reverts to transparent mode.
B. On switches that are configured to operate in client mode, VLANs can be created, deleted, or renamed locally.
C. The local VLAN configuration is updated only when an update that has a higher configuration revision number is received.
D. VTP advertisements are not forwarded to neighboring switches that are configured in VTP transparent mode.
E. VTP client is the default VTP mode.
F. When switches in VTP client mode are rebooted, they send a VTP advertisement request to the VTP servers.

Answer: CF

Pass4sure 200-101 Question Answer

Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.

Answer: DF                                            Passleader 200-101 Exam Qustion

Pass4sure 200-101 Question Answer

What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)

A. Router(config)# interface fastethernet 0/0
Router(config-if)# ip address 192.168.1.1 255.255.255.0 Router(config-if)# no shut down
B. Router(config)# interface fastethernet 0/0
Router(config-if)# no shut down
Router(config)# interface fastethernet 0/0.1
Router(config-subif)# encapsulation dot1q 10
Router(config-subif)# ip address 192.168.10.1 255.255.255.0 Router(config)# interface fastethernet 0/0.2
Router(config-subif)# encapsulation dot1q 20
Router(config-subif)# ip address 192.168.20.1 255.255.255.0
C. Router(config)# router eigrp 100
Router(config-router)# network 192.168.10.0
Router(config-router)# network 192.168.20.0
D. Switch1(config)# vlan database
Switch1(config-vlan)# vtp domain XYZ
Switch1(config-vlan)# vtp server
E. Switch1(config)# interface fastethernet 0/1
Switch1(config-if)# switchport mode trunk
F. Switch1(config)# interface vlan 1
Switch1(config-if)# ip default-gateway 192.168.1.1

Answer: BE

Pass4sure 200-101 Question Answer

Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

A. Host E and host F use the same IP gateway address.
B. Router1 and Switch2 should be connected via a crossover cable.
C. Router1 will not play a role in communications between host A and host D.
D. The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
E. Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
F. The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.

Answer: DF                                                                 

 Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

A. 802.1Q native VLAN frames are untagged by default.
B. 802.1Q trunking ports can also be secure ports.
C. 802.1Q trunks can use 10 Mb/s Ethernet interfaces.
D. 802.1Q trunks require full-duplex, point-to-point connectivity.
E. 802.1Q trunks should have native VLANs that are the same at both ends.

Answer: ACE

Pass4sure 200-101 Question Answer

A technician has configured the FastEthernet 0/1 interface on Sw11 as an access link in VLAN 1. Based on the output from the show vlan brief command issued on Sw12, what will be the result of making this change on Sw11?
 

A. Only the hosts in VLAN 1 on the two switches will be able to communicate with each other.
B. The hosts in all VLANs on the two switches will be able to communicate with each other.
C. Only the hosts in VLAN 10 and VLAN 15 on the two switches will be able to communicate with each other.
D. Hosts will not be able to communicate between the two switches.

Answer: D

Pass4sure 200-101 Question Answer

The output that is shown is generated at a switch. Which three statements are true? (Choose three.)

A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.

Answer: A,C,E

Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state? 

A. converged
B. redundant
C. provisioned
D. spanned

Answer: A